CNCTOPBAOS 3 Axis GRBL 1.1f USB Port CNC Engraving Machine Controller Board
Bottom line: The CNCTOPBAOS 3 Axis GRBL 1.1f USB Port CNC Engraving Machine Controller: GRBL 1.1F firmware works with Candle and Universal Gcode Sender; main trade-off: not plug-and-play; wiring and setup required before first cut.
As an Amazon Associate, SpecPicks earns from qualifying purchases. Full disclosure →
Pros & Cons
Pros
- ✓ GRBL 1.1F firmware works with Candle and Universal Gcode Sender
- ✓ Drop-in for 1310, 1610-PRO, 3018, 3018-PRO and 3018-PRO-MAX
- ✓ Adds emergency-stop, probe, XYZ limit and power-switch ports
- ✓ Full 3-axis XYZ plus spindle PWM speed control 0-100%
- ✓ Runs Nema17/Nema23 steppers; 24VDC spindle over 3-pin PWM/TTL
Cons
- ✗ Not plug-and-play; wiring and setup required before first cut
- ✗ Needs manual CH340 driver install for the COM port to appear
- ✗ Stepper current capped near 1.5A or it runs hot
- ✗ Windows XP/7/8/10 only; no listed macOS or Linux support
SpecPicks Verdict
SpecPicks has no buyer-rating or benchmark data for CNCTOPBAOS 3 Axis GRBL 1.1f USB Port CNC Engraving Machine…, so this read rests on the manufacturer's listed specs (how we evaluate). Compare with similarly-priced alternatives in the controllers & gamepads category before committing. On the listing's own facts, the case for it is "GRBL 1.1F firmware works with Candle and Universal Gcode Sender"; the main trade-off is "Not plug-and-play; wiring and setup required before first cut". If those two points fit how you will use it, put it beside one or two close alternatives in the Compare tool to confirm the price.
Before ordering, check the listed dimensions, ports, power requirements and supported devices or systems in the spec table below against how you plan to use it, and confirm them on the retailer's listing. Prices and stock are set by the retailer and may have moved since this page was last updated.
Key Features
Quoted from the manufacturer's listing. Where it differs from the pros and cons above, those note the conditions the listing leaves out.
- Model: Upgraded 3 Axis GRBL 1.1F USB Port GRBL Control Board; Input voltage: 24VDC
- Support software: GRBL Contol/Candle(3 axis)/Universal Gcode Sender; Support System: Windows XP/7/8/10
- Support Motor: Support XYZ three-axis control, spindle.Support stepper motor: 12V, maximum current of 2A or less is recommended within 1.5A and additional heat. (Any stepper motor Nema17,Nema23);Support spindle: Support 24VDC Spindle PWM speed 0%-100%,also support 3-pin PWM/TTL signal control module
- New functions: Add 2-pin emergency stop button port,probe port,XYZ limit port and add the power button switch;Applications: The control board can be used with the 1310,1610-PRO, 3018,3018-PRO and 3018-PRO MAX etc engraving machines
- IMPORTANT: This is a control board, NOT plug-and-play. Pls Connect 24VDC to board, then connect USB to PC. Driver: Install your CH340 driver. In Device Manager > "Ports", verify "USB-SERIAL CH340 (COMx)" appears. Software: Use GrblControl/Candle. Select same COM port, set baud rate to 115200, click "Connect".Unlock: After connect, click "Unlock" or send $X command Final Check: If connected but no movement, release emergency stop, ensure limit switches off, then click "Reset" & "Unlock"
Full Specifications
| Brand | CNCTOPBAOS |
|---|---|
| Model | Upgraded 3 Axis GRBL 1.1F USB Port GRBL Control Board; Input voltage: 24VDC |
| Connectivity | USB |
| Compatibility | PC, Switch |
| Support software | GRBL Contol/Candle(3 axis)/Universal Gcode Sender; Support System: Windows XP/7/8/10 |
| Batteries required | No |
| Package Dimensions | 5.71 x 4.33 x 3.39 inches |
| Full listing title | CNCTOPBAOS 3 Axis GRBL 1.1f USB Port CNC Engraving Machine Controller Board for CNC Router Engraver Milling Machine 3018-PRO 1610-PRO 3018-PRO-MAX Control Card |
Ready to buy?
CNCTOPBAOS 3 Axis GRBL 1.1f USB Port CNC Engraving Machine Controller Board for CNC Router Engraver Milling Machine 3018-PRO 1610-PRO 3018-PRO-MAX Control Card is listed on Amazon. Price, availability, shipping and returns are set by Amazon and its sellers — check the listing for current terms. SpecPicks earns a small commission on qualifying purchases — thank you for supporting independent review work.
Related Controllers & Gamepads
More guides & deep dives from the SpecPicks archive
Browse all articles & guides →- RTX 4070 Super vs RX 7800 XT — Which to Buy in 2026
- How to Build a Windows 98 Retro PC in 2026
- The Complete Voodoo5 5500 AGP Driver Guide (2026 Edition)
- Best Budget Gaming PC Build 2026 — ~$1,000 Parts List
- Best 1440p Gaming GPUs in 2026
- Best Retro Handhelds in 2026: Pocket, Mid-Tier and FPGA Picks
- Emulation Hardware in 2026: FPGA, Software, and Cart-Reader Ecosystems
More reviews from the SpecPicks archive
Browse all reviews →- Sound Blaster Audigy 2 ZS vs Audigy FX for Windows XP Gaming (2026)
- Best Game Controllers for PC and Console (2026)
- Blue Yeti vs HyperX QuadCast 2 S: Best Streaming Mic 2026
- Best Raspberry Pi Alternative for Emulation (2025)
- Ollama on the RTX 3060 12GB: Model Sizes and tok/s for 2026
- Intel Optane DIMMs Run 1-Trillion-Parameter LLM on One Workstation
- Best Raspberry Pi Alternative for Home Assistant (2026)
- Best PlayStation Controllers for PC Gaming in 2026
- Best Budget Gaming CPU: Ryzen 5 5600G vs 5700X vs i7-9700K
- Asus ROG Xreal R1: 240Hz AR gaming glasses land
- Hyperscalers May Soon Outrun Their Cash Flow on AI Buildout
- How Creative Killed Aureal: The 1999 Patent War, Audigy's Lineage, and Why Consumer PC Audio Stagnated for…
- Intel Arc Pro B60 Price: Is $999 Worth It in 2025?
- Best Internal SATA SSDs for PC Upgrades (2026)
- CompactFlash to IDE Imaging for Win98: Troubleshooting Common Failures
- Best CPU Cooler for AM4 Ryzen Overclocking in 2026
- Crucial BX500 1TB vs Samsung 870 EVO: Best SATA SSD for a Budget or Retro Build (2026)
- Forza Horizon 6 Runs Surprisingly Well on Steam Deck — Here's What Players Are Reporting
- Best Plug-and-Play Retro Gaming Consoles in 2026: 5 Picks
- Sound Blaster Live! Restoration Guide: Period-Correct Audigy FX Bridge for Win98 Builds
- Four Frontier Models in Eight Days: What a 12GB GPU Can Actually Run
- Qualcomm Enters the Data-Center Market With Its Own AI Processor
- DIY Open-Source Photo Frame: Pi Zero 2 W + Immich
- Best CPU Coolers for Ryzen & Intel Gaming Builds in 2026
Earliest SpecPicks reviews
Browse full archive →- Best GPU for Llama 3.1 8B (2026)
- Best GPU for Qwen 3 14B (2026)
- Best GPU for Qwen 3 32B (2026)
- Best GPU for Llama 3.1 70B (2026)
- Best GPU for DeepSeek-R1 32B (2026)
- Best GPU for Llama 3.1 405B (2026)
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 14B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 70B on NVIDIA GeForce RTX 5090
- How to run DeepSeek-R1 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 4090