AITRIP
AITRIP 4PCS 80mm USB Fan 5V Brushless 8025 80x25mm
Bottom line: The AITRIP 4PCS 80mm USB Fan 5V Brushless 8025 80x25mm ($12.99 on Amazon as of 2026-10-06): Four 80x80x25mm fans per pack, enough for a full case, 3D printer or radiator build; main trade-off: 5V USB power only, so no PWM or 3-pin header speed control.
As an Amazon Associate, SpecPicks earns from qualifying purchases. Full disclosure →
*Price sourced from Amazon.com. Last updated 2026-10-06. Price and availability subject to change.
Pros & Cons
Pros
- ✓ Four 80x80x25mm fans per pack, enough for a full case, 3D printer or radiator build
- ✓ 2600 RPM +/-10% moves 30 CFM at a rated 26 dBA
- ✓ Hydraulic bearing rated up to 40,000 hours at 25 degrees C
- ✓ USB plug runs off a power bank, PC port or 5V adapter, no motherboard header needed
Cons
- ✗ 5V USB power only, so no PWM or 3-pin header speed control
- ✗ Listing specs conflict: 2600 vs 2500 RPM, 30 vs 39.7 CFM, hydraulic vs sleeve bearing
- ✗ 35cm cable is short for tower routing without a USB extension
- ✗ 0.27A per fan means about 1.08A pulled from one 5V source with all four running
Manufacturer description
Futures：Size:80x80x25mmRated Voltage: 5VRated Current: 0.25AConnecter: USBSpeed: 2500RPMAir flow:39.7CFMNoise:26dBABearing type: Sleeve BearingCable Length: 35cm Or 13.8 inchesLife: 35000 hoursPackage：4PCS 8025 USB Fan 5V Brushless fan
SpecPicks Verdict
SpecPicks scored AITRIP 4PCS 80mm USB Fan 5V Brushless 8025 80x25mm using a rating × review-volume × price-fit model applied to published specs and reviews across the retro cpu coolers & fans category. AITRIP's retro cpu coolers & fans lineup sits within the broader category mid-tier; price and specs are the deciding factors over brand loyalty here. Judge it on the specification table and the price rather than on sentiment: check the figures that decide your use case, then put it side-by-side with two or three close alternatives in the Compare tool before clicking through.
Common buyer scenarios for retro cpu coolers & fans of this kind: matching it to an existing build, replacing a failing part, or upgrading from a previous-generation equivalent. Check the spec table below against your current setup — particularly socket / form-factor / power-rating fields — and confirm compatibility on the retailer's listing before purchase. Prices and stock are set by the retailer and may have moved since this page was last updated.
Key Features
- Package include: 4pcs 80mm router cooler fan
- High quality 80mm USB Fan, speed 2600 + -10% RPM
- Rated voltage: DC 5V, Rated current: 0.27A
- Wind volume: 30CFM；Noise: 26dBA
- Connector: USB Plug; Bearing Type: Hydraulic Bearing ; Life: working up to 40000h at 25 degrees.
Full Specifications
| Brand | AITRIP |
|---|---|
| Voltage | 5 Volts |
| Wattage | 3 watts |
| Material | Copper |
| Connector | USB Plug; Bearing Type: Hydraulic Bearing ; Life: working up to 40000h at 25 degrees. |
| Unit Count | 4.0 Count |
| Noise Level | 26 Decibels |
| Part Number | 14491_7 |
| Wind volume | 30CFM；Noise: 26dBA |
| Connectivity | USB |
| Compatibility | PC |
| Material Type | Copper |
| Rated voltage | DC 5V, Rated current: 0.27A |
| Cooling Method | Air |
| Number of Items | 4 |
| Package include | 4pcs 80mm router cooler fan |
| Air Flow Capacity | 39.7 Cubic Feet Per Minute |
| Compatible Devices | Desktop, Printer |
| Power Connector Type | USB |
| Maximum Rotational Speed | 2500 RPM |
| Full listing title | AITRIP 4PCS 80mm USB Fan 5V Brushless 8025 80x25mm for Cooling DIY PC Computer Case 3D Printer CPU Coolers Radiators |
Ready to buy?
AITRIP 4PCS 80mm USB Fan 5V Brushless 8025 80x25mm for Cooling DIY PC Computer Case 3D Printer CPU Coolers Radiators is listed on Amazon. Price, availability, shipping and returns are set by Amazon and its sellers — check the listing for current terms. SpecPicks earns a small commission on qualifying purchases — thank you for supporting independent review work.
*Price sourced from Amazon.com. Last updated 2026-10-06. Price and availability subject to change.
Related Retro CPU Coolers & Fans
More guides & deep dives from the SpecPicks archive
Browse all articles & guides →- Best Retro Handhelds in 2026 — From $35 to $500
- RTX 4070 Super vs RX 7800 XT — Which to Buy in 2026
- The Complete Voodoo5 5500 AGP Driver Guide (2026 Edition)
- Best 1440p Gaming GPUs in 2026
- How to Build a Windows 98 Retro PC in 2026
- Best Budget Gaming PC Build 2026 — ~$1,000 ($800 on Sale)
- Emulation Hardware in 2026: FPGA, Software, and Cart-Reader Ecosystems
More reviews from the SpecPicks archive
Browse all reviews →- Best Controller for Steam Deck Docked Mode in 2026
- CompactFlash as a Retro PC Boot Drive: The 2026 CF-to-IDE Build Guide
- Best Gaming CPU for 1080p and 1440p Builds in 2026
- Best Way to Stream a PS4 Pro to PC: Elgato Cam Link 4K Capture Setup
- Logitech G502 Hero vs MK270 Combo: Best PC Setup for Sub-$50
- Raspberry Pi 5 Power Supply: What You Actually Need (2026)
- Why That Game Boy Clone Runs Too Fast — and the Crystal Fix
- Ryzen AI Max LLM Test: What the Public Data Shows
- Microsoft's SkillOpt Boosts Models With Just a Markdown File — What It Means for Your Local RTX 3060 Rig
- How to run Qwen 3 32B on Apple M4 (2026)
- Steam Deck OLED vs Legion Go S: 2026 Comparison
- Best GPU for Llama 3.1 405B (2026)
- Ryzen 5 5600G vs Ryzen 7 5700X vs Ryzen 7 5800X for 1080p Gaming in 2026
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 5070
- Can a Local RTX 3060 12GB LLM Debug Linux Boot Like Gemini?
- Best GPU for Local LLMs in 2026: Why the RTX 3060 12GB Still Wins on Value
- Fable 5 as Manager: The Delegate-to-Sonnet-5 Cost Pattern
- How to Run a SATA SSD on a Windows XP Retro Gaming PC (AHCI + Adapters)
- Build a Jellyfin Home Media Server on a Raspberry Pi 4 (8GB) in 2026
- Count Anything Runs Locally on a 12GB GPU: Object-Counting AI on the RTX 3060
- Intel Core Ultra 5 250K Plus vs Ryzen 5 7600X3D: The Mid-Range Faceoff
- MTP in llama.cpp: The Regression, the Fix, and the KV-Cache Free Lunch
- AI-Driven Sound Blaster Driver Recovery on Win98 in 2026
- Raspberry Pi vs AMD GPUs for Local LLMs: What the Specs Show
Earliest SpecPicks reviews
Browse full archive →- Best GPU for Llama 3.1 8B (2026)
- Best GPU for Qwen 3 14B (2026)
- Best GPU for Qwen 3 32B (2026)
- Best GPU for Llama 3.1 70B (2026)
- Best GPU for DeepSeek-R1 32B (2026)
- Best GPU for Llama 3.1 405B (2026)
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 14B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 70B on NVIDIA GeForce RTX 5090
- How to run DeepSeek-R1 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 4090