HOZLY 1/8" Carbide Square End Mill for Aluminum Copper Applications
Bottom line: The HOZLY 1/8" Carbide Square End Mill for Aluminum Copper Applications: 10 end mills per pack, each with a 1/8-inch (3.175mm) cutting diameter and shank; main trade-off: 15mm flute length limits depth of cut per pass.
As an Amazon Associate, SpecPicks earns from qualifying purchases. Full disclosure →
Pros & Cons
Pros
- ✓ 10 end mills per pack, each with a 1/8-inch (3.175mm) cutting diameter and shank
- ✓ DLC coating lowers friction and resists chip buildup on aluminum and copper
- ✓ 35-degree helix angle clears chips quickly in soft non-ferrous alloys
- ✓ 3-flute solid carbide geometry suited to slotting in aluminum, zinc, magnesium
Cons
- ✗ 15mm flute length limits depth of cut per pass
- ✗ 38mm overall length leaves little stick-out for deep pockets
- ✗ Not listed for steel, stainless, or other ferrous materials
- ✗ Requires a 1/8-inch (3.175mm) collet or adapter on your spindle
SpecPicks Verdict
SpecPicks has no buyer-rating or benchmark data for HOZLY 1/8" Carbide Square End Mill for Aluminum Copper Applications, so this read rests on the manufacturer's listed specs (how we evaluate). Compare with similarly-priced alternatives in the displays & upscalers category before committing. On the listing's own facts, the case for it is "10 end mills per pack, each with a 1/8-inch (3.175mm) cutting diameter and shank"; the main trade-off is "15mm flute length limits depth of cut per pass". If those two points fit how you will use it, put it beside one or two close alternatives in the Compare tool to confirm the price.
Before ordering, check the listed dimensions, ports, power requirements and supported devices or systems in the spec table below against how you plan to use it, and confirm them on the retailer's listing. Prices and stock are set by the retailer and may have moved since this page was last updated.
Key Features
Quoted from the manufacturer's listing. Where it differs from the pros and cons above, those note the conditions the listing leaves out.
- 【Material】: Cnc 3-Flute Solid Carbide Spiral Router Bit.For Aluminum Alloy And Copper Alloy, Magnesium Alloy, Zinc Alloy,Acrylic, Plywood, OAK, MDF, and Any Hardwood,Etc.
- 【DLC Coating】:Dlc(Diamond-Like Carbon) Coating Has Ultra-High Hardness,Low Friction Coefficient, High Temperature Resistance, Good Electrical Insulation, Chemical Barrier, High Thermal Conductivity, Ultra-High Anti-Blocking Performance.
- 【Adventage】:Surface Finishes Are Greatly Improved No Matter If You Are Roughing Or Finishing Due To Effective Chip Removal; Cut Faster Thanks To Superior Material Removal Rate (Mrr) Especially When Slotting.
- 【The 35 Degree Helix Angle Design】 According To The Characteristics Of Soft Materials Such As Aluminum Alloy And Copper Alloy, It Adopts A 35 Degree Large Helix Angle Design.Greatly Improves The Production Efficiency, Sharp And Durable, Convenient For Chip Removal.
- 【Package Included】: 10Pcs 3 Flutes End Mill Cutter.Cutting Diameter: 3.175mm,1/8inch ,Flute Length:15mm ,Full Length:38mm ,Shank Diameter: 3.175mm,1/8inch.
Full Specifications
| Size | 3.175*3.175*15mm |
|---|---|
| Brand | HOZLY |
| Model | 3958077 |
| Cut Type | Finishing, Roughing, Square |
| Material | Carbide |
| Size Name | 3.175*3.175*15mm |
| Part Number | 3958077 |
| Item Diameter | 0.13 inches |
| Material Type | Carbide |
| Cutting Length | 38 millimeters |
| Number of Items | 10 |
| Number of Packs | 10 |
| Cutting Diameter | 0.13 inches |
| Number of Flutes | 3 |
| Included Components | Carbide Square End Mil |
| Full listing title | 1/8" Carbide Square End Mill for Aluminum Copper Applications, 3-Flute,1/8" Cutting Diameter,DLC Coating, CNC Router Bits, End Mill Bits, U-Type Design, 10-Pack (3.175 * 3.175 * 15mm) |
Ready to buy?
1/8" Carbide Square End Mill for Aluminum Copper Applications, 3-Flute,1/8" Cutting Diameter,DLC Coating, CNC Router Bits, End Mill Bits, U-Type Design, 10-Pack (3.175 * 3.175 * 15mm) is listed on Amazon. Price, availability, shipping and returns are set by Amazon and its sellers — check the listing for current terms. SpecPicks earns a small commission on qualifying purchases — thank you for supporting independent review work.
More guides & deep dives from the SpecPicks archive
Browse all articles & guides →- Best Retro Handhelds in 2026: Pocket, Mid-Tier and FPGA Picks
- Emulation Hardware in 2026: FPGA, Software, and Cart-Reader Ecosystems
- Best 1440p Gaming GPUs in 2026
- Best Budget Gaming PC Build 2026 — ~$1,000 Parts List
- RTX 4070 Super vs RX 7800 XT — Which to Buy in 2026
- How to Build a Windows 98 Retro PC in 2026
- The Complete Voodoo5 5500 AGP Driver Guide (2026 Edition)
More reviews from the SpecPicks archive
Browse all reviews →- Retro Games With 1:1 Remakes: The Faithful Rebuild List
- Best Adaptive and One-Handed Gaming Controllers in 2026
- Best Gaming SSD for PC Builds in 2026: 5 Picks Tested
- Qwen 3.6 vs Frontier Models on a Local Rig: The Honest Gap
- Can an RTX 3060 12GB Drive a 27-Inch 4K Monitor in 2026?
- KOORUI 27" 4K vs Samsung Odyssey 27" 4K for PS5 and PC Gaming
- 3dfx Voodoo 5 5500 Install Troubleshooting on Windows 98 SE: Drivers, IRQs, and Glide Wrapper Fixes
- Best USB Microphone for Streaming in 2026: HyperX QuadCast 2 vs Blue Yeti
- Intel Eyed as TSMC Backup by Google and Nvidia for AI Chips
- Best Gaming Mouse Pad for Esports & Office Use in 2026
- Best IDE & SATA-to-USB Adapters for Retro PC Builds in 2026
- Linux Gaming Is Getting Faster: Windows APIs Hit the Kernel
- 42 LLMs Tested for Apocalypse Compliance: What Data Shows
- Intel Arc LLM Performance: A770, B580 & Pro B60 Guide 2025
- Retro Nintendo Switch 2 Dock Channels the N64 and Holds Six Game Cards
- Boot Windows 98 from CompactFlash: Transcend CF133 + IDE Adapter Guide
- Vision LLMs Driving Win98 Driver Installs: Inside Our 4-PC Retro Fleet
- Best Budget AM4 CPU for a 2026 AI + Gaming Build: 5800X vs 5700X vs 5600G
- Why LLM Reasoning Still Happens in Words, Not Vectors
- Cyberdeck Raspberry Pi 4/5 Mini Music Workstation Build Guide
- AMD Ryzen AI Halo Mini PC: Open-Source Power Analyzed
- RTX 3080 vs RTX 5080 — is it time to upgrade?
- Vision LLMs Driving Period-Correct WinXP and Win98 Installers: Field Report from a 4-PC Retro Fleet
- News: ChatGPT Now Listens and Talks at Once
Earliest SpecPicks reviews
Browse full archive →- Best GPU for Llama 3.1 8B (2026)
- Best GPU for Qwen 3 14B (2026)
- Best GPU for Qwen 3 32B (2026)
- Best GPU for Llama 3.1 70B (2026)
- Best GPU for DeepSeek-R1 32B (2026)
- Best GPU for Llama 3.1 405B (2026)
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 14B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 70B on NVIDIA GeForce RTX 5090
- How to run DeepSeek-R1 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 4090