Skip to main content
Flirc Raspberry Pi 3 Case
Flirc

Flirc Raspberry Pi 3 Case

Bottom line: The Flirc Raspberry Pi 3 Case: Entire aluminum body acts as a passive heat sink - no fan, no noise; main trade-off: no Raspberry Pi 4 or 5 support - Pi 3-era boards only.

Check price on Amazon

As an Amazon Associate, SpecPicks earns from qualifying purchases. Full disclosure →

Mike Perry — Hardware researcher since 2014. For emulation handhelds, FPGA consoles and flash carts, synthesises manufacturer documentation, community compatibility lists and independent reviews rather than first-hand lab testing. Core beat: GPU performance across gaming, rendering, and local-LLM inference.

Pros & Cons

Pros

  • ✓ Entire aluminum body acts as a passive heat sink - no fan, no noise
  • ✓ Ships with thermal pad and 4 screws, so nothing extra to buy
  • ✓ Fits Raspberry Pi 3 B+, 3, 2 and B+ on one case
  • ✓ GPIO header and main ports reachable through the case bottom

Cons

  • ✗ No Raspberry Pi 4 or 5 support - Pi 3-era boards only
  • ✗ Passive cooling only; heavy overclocks may still need airflow
  • ✗ GPIO access is bottom-routed, awkward for thick HAT ribbon cables
  • ✗ Aluminum shell blocks any onboard status LEDs from view

Manufacturer description

The Flirc Raspberry Pi 3 Case turns your Pi into something you can leave out on a shelf. Instead of the usual plastic clamshell, Flirc machines the shell from aluminum and uses the entire case body as a passive heat sink: a thermal pad bridges the SoC to the metal core, so the Pi sheds heat silently with no fan and no vents whining under emulation load. Assembly takes four screws and a few minutes. Compatibility spans the Raspberry Pi 3 B+, Pi 3, Pi 2, and B+ boards, which makes it a practical fit for RetroPie, Kodi, and Lakka builds you plan to keep running. The GPIO header and the main…

SpecPicks Verdict

SpecPicks has no buyer-rating or benchmark data for Flirc Raspberry Pi 3 Case, so this read rests on the manufacturer's listed specs (how we evaluate). Compare with similarly-priced alternatives in the emulation hardware category before committing. On the listing's own facts, the case for it is "Entire aluminum body acts as a passive heat sink - no fan, no noise"; the main trade-off is "No Raspberry Pi 4 or 5 support - Pi 3-era boards only". If those two points fit how you will use it, put it beside one or two close alternatives in the Compare tool to confirm the price.

Before ordering, check the listed dimensions, ports, power requirements and supported devices or systems in the spec table below against how you plan to use it, and confirm them on the retailer's listing. Prices and stock are set by the retailer and may have moved since this page was last updated.

Frequently Asked Questions

Does the Flirc case fit a Raspberry Pi 4 or Pi 5?

No. Flirc lists this case for the Raspberry Pi 3 B+, Pi 3, Pi 2 and B+ models. Flirc sells separate cases for newer boards, so check the listing for your exact Pi revision before ordering.

Do I need a fan with this case?

No. The case is built around an internal heat sink that mates to the SoC through the included thermal pad, using the aluminum body itself as the cooling surface. It runs completely fanless and silent.

Can I still use the GPIO pins?

Yes. The GPIO header and all the main connectors are accessible through the bottom of the case, so you can route a ribbon cable or jumper wires out without modifying the enclosure.

What comes in the box?

The case, a thermal pad, and four screws. That is everything needed to mount the board - no separate heat sinks or standoffs required.

Is this a good case for a RetroPie or Kodi build?

Yes. Silent passive cooling and an aluminum finish suit a living-room or desk setup where fan noise is noticeable.

Key Features

Quoted from the manufacturer's listing. Where it differs from the pros and cons above, those note the conditions the listing leaves out.

  • The best looking Raspberry Pi case made out of beautiful aluminum
  • All New Manufacturing Process with improved metal quality and design
  • Made for the new Raspberry Pi 3 B+, works with Raspberry Pi 3, 2 and B+ Models
  • GPIO and all the main connectors are easily accessible through the bottom
  • Built in Heat Sink and comes with a thermal pad and 4 screws

Full Specifications

BrandFlirc
ColorSilver
Fan Size8 centimeters
MaterialMetal
Case TypeRaspberry Pi
Model NameFlirc Raspberry Pi 3B Case
Light ColorEnhanced
Model NumberFL-70462
Cooling MethodAir
Number of Fans2
Mfr Part NumberFL-70462
Total Usb Ports4
Antenna LocationBusiness
Compatible DevicesRaspberry Pi 3
Enclosure MaterialMetal
Warranty Description1 year manufacturer warranty
Hard Disk Form Factor2.5 inches
Supported MotherboardRaspberry Pi Model 3
Motherboard CompatabilityRaspberry Pi Model 3
Power Supply Mounting TypeBottom Mount

Ready to buy?

Flirc Raspberry Pi 3 Case is listed on Amazon. Price, availability, shipping and returns are set by Amazon and its sellers — check the listing for current terms. SpecPicks earns a small commission on qualifying purchases — thank you for supporting independent review work.

Check price on Amazon →

Related Emulation Hardware

More guides & deep dives from the SpecPicks archive

Browse all articles & guides →

More reviews from the SpecPicks archive

Browse all reviews →

Earliest SpecPicks reviews

Browse full archive →