Skip to main content
GLOTRENDS 100mm PCIe 3.0 X1 Riser Cable for M.2, WiFi, Firewire, USB, Sound Cards, etc
GLOTRENDS

GLOTRENDS 100mm PCIe 3.0 X1 Riser Cable for M.2, WiFi, Firewire, USB, Sound Cards, etc

Bottom line: The GLOTRENDS 100mm PCIe 3.0 X1 Riser Cable for M.2: Dual 90-degree right-angle ends for tight routing in cramped cases; main trade-off: X4, X8 and X16 cards are limited to X1 speed.

Check price on Amazon

As an Amazon Associate, SpecPicks earns from qualifying purchases. Full disclosure →

Mike Perry — Hardware researcher since 2014. For retro PC hardware and period-correct parts, synthesises manufacturer documentation, community compatibility lists and marketplace listings rather than first-hand lab testing. Core beat: GPU performance across gaming, rendering, and local-LLM inference.

Pros & Cons

Pros

  • ✓ Dual 90-degree right-angle ends for tight routing in cramped cases
  • ✓ Full 36-pin X1 signal set supports capture, RAID, NIC and sound cards
  • ✓ Female end physically accepts X1, X4, X8 and X16 cards
  • ✓ Up to 8Gbps on PCIe 3.0 X1, backward compatible with PCIe 2.0 and 1.0
  • ✓ EMI-shielded cable helps keep the signal stable

Cons

  • ✗ X4, X8 and X16 cards are limited to X1 speed
  • ✗ No support for PCIe 4.0 features
  • ✗ 100mm length limits how far you can move a card
  • ✗ Fixed right-angle ends may not suit every slot or case orientation

Manufacturer description

The GLOTRENDS 100mm PCIe 3.0 X1 riser cable extends a single x1 slot, so you can mount an expansion card where your motherboard layout won't let it sit directly. Both ends are bent at 90 degrees, at the X1 male connector and at the X1 female connector. That helps you route the short 100mm run around coolers, graphics cards and cramped small-form-factor cases. The cable carries the full 36-pin PCIe X1 signal set, so it works with the cards x1 slots usually host: M.2 adapters, WiFi cards, FireWire and USB controllers, sound cards, 2.5G diskless boot cards, remote switch cards, capture cards…

SpecPicks Verdict

SpecPicks has no buyer-rating or benchmark data for GLOTRENDS 100mm PCIe 3.0 X1 Riser Cable for M.2, so this read rests on the manufacturer's listed specs (how we evaluate). Compare with similarly-priced alternatives in the expansion cards category before committing. On the listing's own facts, the case for it is "Dual 90-degree right-angle ends for tight routing in cramped cases"; the main trade-off is "X4, X8 and X16 cards are limited to X1 speed". If those two points fit how you will use it, put it beside one or two close alternatives in the Compare tool to confirm the price.

Before ordering, confirm the board side: this card needs a free PCIe 3.0 x1 slot. Your motherboard manual lists which slots share lanes with M.2 sockets or other slots. Prices and stock are set by the retailer and may have moved since this page was last updated.

Frequently Asked Questions

Can I plug an X16 card into this riser cable?

Yes. The female X1 end can take PCIe X1, X4, X8 and X16 cards, but any card connected through it runs at PCIe X1 speed only.

Will this riser work in a PCIe 4.0 motherboard slot?

It is a PCIe 3.0 X1 cable with a maximum of 8Gbps and is backward compatible with PCIe 2.0 and 1.0. It cannot support PCIe 4.0 features, so the link runs at PCIe 3.0 X1 at most.

What kinds of cards can I use with it?

Because it is a full-function 36-pin PCIe X1 cable, it supports X1-class cards such as M.2 adapters, WiFi cards, FireWire and USB controllers, sound cards, 2.5G diskless boot cards, remote switch cards, capture cards and SSD RAID cards.

How long is the cable and which way do the connectors face?

The cable is 100mm long. Both ends are 90-degree right angles, one at the X1 male connector and one at the X1 female connector. Check that this orientation fits your slot and case before you buy.

Will the riser add noise to a sound or capture card?

The cable uses an EMI-shielded design meant to keep the signal clean and the connection stable. Results still depend on your case layout and the cards around it.

Key Features

Quoted from the manufacturer's listing. Where it differs from the pros and cons above, those note the conditions the listing leaves out.

  • PCI-Express 3.0 X1 to X1 extension cable
  • Dual 90 degree right angle: 90 degree right angle at X1 male interface, and 90 degree right angle at X1 female interface.
  • PCIe X1 female interface can be installed with PCIe X1/X4/X8/X16 adapter, but only PCIe X1 speed.
  • 8Gbps speed at max for PCI-Express 3.0 X1 bandwidth, backward compatible with PCIe 2.0/1.0. (Note: can not support PCIe 4.0 feature)
  • 36PIN full function PCIe X1 cable, support all kinds of PCIe cards, such as 2.5G Diskless Boot Card, Remote Switch Card, Capture Card, SSD RAID card, etc.
  • The EMI-shielded design ensures signal integrity and stable performance.

Full Specifications

BrandGLOTRENDS
ColorBlack
ModelPCIE30-X1-100MM-9090D
Weight2.5g
Frequency8 GHz
Cable TypeThe core is tinned copper wrapped in Teflon with a PVC protective coating on the outside
Item ShapeFlat
Model NamePCIE30-X1
Unit Count1.0 Count
Part NumberPCIE30-X1
ConnectivityUSB, WiFi
CompatibilitySwitch
Connector TypeFemale: 90 Degree, Male: -90 Degree
Item Type NamePCIe 3.0 X1 Riser Cable
Number of Pins36
Number of Items1
Special Feature100mm length, -90 to 90 degree conversion
Connector GenderMale-to-Female
Compatible DevicesM.2, WiFi, Firewire, USB, Sound Cards
Data Transfer Rate1 Gigabytes Per Second

Ready to buy?

GLOTRENDS 100mm PCIe 3.0 X1 Riser Cable for M.2, WiFi, Firewire, USB, Sound Cards, etc is listed on Amazon. Price, availability, shipping and returns are set by Amazon and its sellers — check the listing for current terms. SpecPicks earns a small commission on qualifying purchases — thank you for supporting independent review work.

Check price on Amazon →

Related Expansion Cards

More guides & deep dives from the SpecPicks archive

Browse all articles & guides →

More reviews from the SpecPicks archive

Browse all reviews →

Earliest SpecPicks reviews

Browse full archive →