Skip to main content
CQRobot Enclosed Speakers 3 Watt RMS 8 Ohm for Arduino 70mm (L)×31mm (W) | Front-Firing, JST PH2.0 2-Pin Lead Wires, Rectangular, 4 Corner Mounting Holes, for Electronic DIY Projects, 1 Pair
CQRobot

CQRobot Enclosed Speakers 3 Watt RMS 8 Ohm for Arduino 70mm (L) ×31mm (W)

Bottom line: The CQRobot Enclosed Speakers 3 Watt RMS 8 Ohm for Arduino 70mm ×31mm ($7.99 on Amazon as of 2026-11-20 23:20 UTC): Enclosed housing, so no DIY speaker cabinet needed; main trade-off: 8 ohm rating carries a wide plus/minus 15% tolerance.

$7.99 on Amazon, checked (price may vary)

As an Amazon Associate, SpecPicks earns from qualifying purchases. Full disclosure →

Mike Perry — Hardware researcher since 2014, focused on GPU performance across gaming, rendering, and local-LLM inference. Synthesises community benchmarks, manufacturer specs, and public forum data into actionable buying guides.

*Price sourced from Amazon.com. Last updated 2026-11-20. Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.

Pros & Cons

Pros

  • ✓ Enclosed housing, so no DIY speaker cabinet needed
  • ✓ Rated 3.0W, 3.5W max, enough for alerts, voice and game audio
  • ✓ Compact 70 x 31 x 16 mm footprint fits tight project cases
  • ✓ JST PH2.0 2-pin leads plug straight into matching amp boards
  • ✓ Pair in the box makes a left/right stereo setup simple

Cons

  • ✗ 8 ohm rating carries a wide plus/minus 15% tolerance
  • ✗ 3.5W max power limits volume for room-filling playback
  • ✗ JST PH2.0 plug needs an adapter for breadboard jumper wires
  • ✗ Passive speaker, so you need an amplifier module to drive it

Manufacturer description

The CQRobot Enclosed Speakers give your Arduino, Raspberry Pi or robotics build clear, front-facing audio without you having to make a cabinet. Each pack holds one pair of rectangular enclosed speakers rated at 3.0W, with a 3.5W maximum and 8 ohm impedance (plus or minus 15%). Each enclosure measures 70 x 31 x 16 mm (3.1 x 1.2 x 0.63 in), so it fits behind a panel, inside a robot chassis or in the case of a small game machine. The front-firing design points the sound straight out through your faceplate. Four corner mounting holes let you screw each speaker flat against a surface, so it won't…

SpecPicks Verdict

SpecPicks has no buyer-rating or benchmark data for CQRobot Enclosed Speakers 3 Watt RMS 8 Ohm for Arduino 70mm ×31mm, so this read rests on the manufacturer's listed specs and the current price in the motherboards category (how we evaluate). Compare with similarly-priced alternatives in the motherboards category before committing. On the listing's own facts, the case for it is "Enclosed housing, so no DIY speaker cabinet needed"; the main trade-off is "8 ohm rating carries a wide plus/minus 15% tolerance". If those two points fit how you will use it, put it beside one or two close alternatives in the Compare tool to confirm the price.

Common buyer scenarios for motherboards of this kind: matching it to an existing build, replacing a failing part, or upgrading from a previous-generation equivalent. Check the spec table below against your current setup — particularly socket / form-factor / power-rating fields — and confirm compatibility on the retailer's listing before purchase. Prices and stock are set by the retailer and may have moved since this page was last updated.

Frequently Asked Questions

Can I connect the CQRobot speaker directly to an Arduino or Raspberry Pi?

These are passive 3W, 8 ohm speakers with JST PH2.0 2-pin leads. For proper volume, connect them through an amplifier module or an audio board with a matching JST PH2.0 speaker output rather than straight to a GPIO pin.

What are the exact dimensions of each speaker?

Each enclosed speaker measures 70 mm x 31 mm x 16 mm (3.1 x 1.2 x 0.63 inches), length by width by thickness.

How many speakers come in the package?

The listing is for 1 pair, so you get two enclosed speakers. That covers left and right stereo channels or two separate mono outputs.

How do I mount these speakers in my project?

Each rectangular enclosure has 4 corner mounting holes for screwing it to a panel or chassis. The front-firing design means you should face the speaker toward an opening or grille in your case.

What power and impedance do these speakers handle?

They are rated at 3.0W with a 3.5W maximum and an impedance of 8 ohms, plus or minus 15%. Pick an amplifier rated for 8 ohm loads that won't push past 3.5W per channel.

Key Features

Quoted from the manufacturer's listing. Where it differs from the pros and cons above, those note the conditions the listing leaves out.

  • Power: Rated Power / Maximum Power 3.0W / 3.5W.
  • Impedance: 8 Ohms Plus/Minus 15%.
  • Size: 70 mm * 31 mm * 16 mm / 3.1 inch * 1.2 inch * 0.63 inch (L* W * T).
  • Compatible With Arduino, Robot, Raspberry Pi, Advertising Machine, Game Machine, Integrated Machine Special Speaker etc, Projects.
  • For more information, please refer to the Wiki page: Stereo_Enclosed_Speaker_(3_W,_8_ohm)-CQR0508.

Full Specifications

Size70 mm * 31 mm * 16 mm / 3.1 inch * 1.2 inch * 0.63 inch (L* W * T).
BrandCQRobot
ColorSpeaker 3 Watt 8 Ohm-JST-PH2.0 Interface
PowerRated Power / Maximum Power 3.0W / 3.5W.
Impedance8 ohm
Model NameJST PH2.0
Unit Count2 Count
Model NumberCQRANQI0007US
Power SourceCorded Electric
Speaker Size16 millimeters
Speaker Typebass
Input Voltage1 volts
Is WaterproofFALSE
Mounting TypeWall Mount
Series Number7
Warranty TypeLimited
Built-In Media2 * Passive Speaker 3 Watt 8 Ohm(JST-PH2.0 Interface)
Control MethodTouch
Controller TypeTouchpad
Number of Items1
Full listing titleCQRobot Enclosed Speakers 3 Watt RMS 8 Ohm for Arduino 70mm (L)×31mm (W) | Front-Firing, JST PH2.0 2-Pin Lead Wires, Rectangular, 4 Corner Mounting Holes, for Electronic DIY Projects, 1 Pair

Benchmark data for other processors

Ready to buy?

CQRobot Enclosed Speakers 3 Watt RMS 8 Ohm for Arduino 70mm (L)×31mm (W) | Front-Firing, JST PH2.0 2-Pin Lead Wires, Rectangular, 4 Corner Mounting Holes, for Electronic DIY Projects, 1 Pair is listed on Amazon. Price, availability, shipping and returns are set by Amazon and its sellers — check the listing for current terms. SpecPicks earns a small commission on qualifying purchases — thank you for supporting independent review work.

Buy on Amazon — $7.99

*Price sourced from Amazon.com. Last updated 2026-11-20. Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.

Related Motherboards

More guides & deep dives from the SpecPicks archive

Browse all articles & guides →

More reviews from the SpecPicks archive

Browse all reviews →

Earliest SpecPicks reviews

Browse full archive →