UMLIFE 4PCS 3D Printer Cooling Fan 40mmx40mmx10mm Oil Bearing Blower Fan DC 12V Brushless Cooling Fan with 2 Pin Terminal for Hotend Extruder Heatsinks Makerbot MK7 MK8 CPU Chip (12V 0.08A)
Bottom line: The UMLIFE 4PCS 3D Printer Cooling Fan 40mmx40mmx10mm Oil Bearing Blower: Four fans per pack, so you keep spares on hand for hotend swaps; main trade-off: 12V only; 24V printers need a step-down converter or a 24V fan.
As an Amazon Associate, SpecPicks earns from qualifying purchases. Full disclosure →
Pros & Cons
Pros
- ✓ Four fans per pack, so you keep spares on hand for hotend swaps
- ✓ Standard 40x40x10mm size fits MK7/MK8-style hotend heatsinks
- ✓ Rated 27dBA at 6000RPM for quiet hotend cooling
- ✓ Pre-fitted 2-pin PH2.5 connector on a 30cm (11.8in) lead
- ✓ Low 0.08A draw at DC 12V is easy on board fan headers
Cons
- ✗ 12V only; 24V printers need a step-down converter or a 24V fan
- ✗ Oil bearing rather than ball bearing; may wear faster in hot enclosures
- ✗ Some units may need the red and black wires swapped to spin
- ✗ 2-wire lead has no tach signal for RPM monitoring
Manufacturer description
The UMLIFE 40mm 3D printer cooling fan comes as a 4-pack of 12V brushless fans. Each one measures 40 x 40 x 10mm, the usual size for hotend heatsinks on MakerBot MK7 and MK8-style extruders. Each fan spins at 6000RPM, draws 0.08A at DC 12V and is rated at 27dBA. That gives you steady airflow across the heatsink without adding much noise to a long print. Installation is simple. Every fan comes with a 2-pin PH2.5 connector already fitted on a 30cm (11.8in) lead, so you have room to route the cable along the carriage to your control board. If a fan does not spin when you first power it on…
SpecPicks Verdict
SpecPicks has no buyer-rating or benchmark data for UMLIFE 4PCS 3D Printer Cooling Fan 40mmx40mmx10mm Oil Bearing Blower…, so this read rests on the manufacturer's listed specs (how we evaluate). Compare with similarly-priced alternatives in the retro cpu coolers & fans category before committing. On the listing's own facts, the case for it is "Four fans per pack, so you keep spares on hand for hotend swaps"; the main trade-off is "12V only; 24V printers need a step-down converter or a 24V fan". If those two points fit how you will use it, put it beside one or two close alternatives in the Compare tool to confirm the price.
Common buyer scenarios for retro cpu coolers & fans of this kind: matching it to an existing build, replacing a failing part, or upgrading from a previous-generation equivalent. Check the spec table below against your current setup — particularly socket / form-factor / power-rating fields — and confirm compatibility on the retailer's listing before purchase. Prices and stock are set by the retailer and may have moved since this page was last updated.
Frequently Asked Questions
Will this fan fit my MK8 hotend heatsink?
The fan measures 40 x 40 x 10mm and is listed for MakerBot MK7 and MK8-style hotend heatsinks. Confirm that your fan shroud or bracket takes a 40mm, 10mm-thick fan before installing.
Can I use this fan on a 24V 3D printer?
Not directly. It is rated for DC 12V at 0.08A. On a 24V board, use a 24V fan or add a step-down converter to supply 12V to the fan header.
What connector does it use and how long is the cable?
Each fan has a 2-pin PH2.5 connector already fitted on a 30cm (11.8in) cable, so it is ready to plug in out of the box.
My new fan does not spin. What should I do?
UMLIFE says that swapping the red and black wires in the plug fixes the problem. Also confirm that the header supplies 12V, not 24V or 5V.
How fast and how loud is this 40mm fan?
It is rated at 6000RPM with a noise level of 27dBA, and it uses an oil bearing with a brushless DC motor.
Key Features
Quoted from the manufacturer's listing. Where it differs from the pros and cons above, those note the conditions the listing leaves out.
- ☀☀ Power Connection: 2 Pin-ph2.5; Cable length is 30cm/11.8in. Connector is already fitted and product is out-of-the-box ready for installation.
- ☀☀ Great replacement item for your all metal hotend or maybe a small cooling fan for your 3D printer nozzle setup.
- ☀☀ Made of high quality plastics with high end bearings, this 3D printer part cooling fan can run continuously for days at high speeds without hassle or concern.
- ☀☀ Size:40mm*40mm*10mm(L*D*H), Speed:6000RPM, Noise:27dBA, Bearing: oil, DC 12V, 0.08A.
- ☀☀ Note: If you meet the fans did not work, you can swap the red and black wires in the plug got it to work. (Any questions, you can contact us and we will give you a satisfied solution!).
Full Specifications
| Brand | UMLIFE |
|---|---|
| Model | 4010-12V |
| Voltage | 12 Volts |
| Material | Plastic |
| Noise Level | 27 Decibels |
| Part Number | 4010-12V |
| ☀☀ Size | 40mm*40mm*10mm(L*D*H), Speed:6000RPM, Noise:27dBA, Bearing: oil, DC 12V, 0.08A. |
| Material Type | Plastic |
| Cooling Method | Air |
| Number of Items | 4 |
| Air Flow Capacity | 6.5 Cubic Feet Per Minute |
| Compatible Devices | Printer |
| Power Connector Type | 2-Pin |
| ☀☀ Power Connection | 2 Pin-ph2.5; Cable length is 30cm/11.8in. Connector is already fitted and product is out-of-the-box ready for installation. |
| Maximum Rotational Speed | 6000 RPM |
| Item Dimensions L x W x H | 3.94"L x 15.75"W x 15.75"H |
Benchmark data for other processors
Ready to buy?
UMLIFE 4PCS 3D Printer Cooling Fan 40mmx40mmx10mm Oil Bearing Blower Fan DC 12V Brushless Cooling Fan with 2 Pin Terminal for Hotend Extruder Heatsinks Makerbot MK7 MK8 CPU Chip (12V 0.08A) is vintage hardware; the used and vintage market on eBay carries most of the live inventory. Prices and condition vary by seller and move in real time, so we link the live listing rather than quote a cached price. It also has an Amazon listing — check it for current price and availability. SpecPicks earns a small commission on qualifying purchases — thank you for supporting independent review work.
Related Retro CPU Coolers & Fans
More guides & deep dives from the SpecPicks archive
Browse all articles & guides →- The Complete Voodoo5 5500 AGP Driver Guide (2026 Edition)
- Emulation Hardware in 2026: FPGA, Software, and Cart-Reader Ecosystems
- Best 1440p Gaming GPUs in 2026
- How to Build a Windows 98 Retro PC in 2026
- Best Retro Handhelds in 2026: Pocket, Mid-Tier and FPGA Picks
- RTX 4070 Super vs RX 7800 XT — Which to Buy in 2026
- Best Budget Gaming PC Build 2026 — ~$1,000 Parts List
More reviews from the SpecPicks archive
Browse all reviews →- Microsoft Now Points to 32GB RAM for Windows 11 Gaming
- Best Game Controller for PC in 2026: 5 Picks Tested Against Real Use
- Build a Raspberry Pi 4 8GB RetroPie Emulation Station in 2026
- Ryzen 7 9800X3D vs Ryzen 9 9900X: Which Zen 5 CPU Wins in 2026?
- Best CPU Cooler for AM4 Ryzen Overclocking (2026 Edition)
- Ryzen 7 5800X vs Ryzen 7 5700X for 1440p Gaming: Is the Premium Worth It?
- Ryzen AI Max Mini-ITX: Framework Desktop Specs Explained
- AMD's Ryzen 7 7700X3D Goes Newegg-Exclusive at $329
- AMD Ryzen AI Max+ PRO 495 192GB: What the PassMark Leak Tells Us
- Build a Raspberry Pi 4 NAS With an SSD in 2026
- No Wonder My CPU Was Hitting 100°C: 7 Build Mistakes
- Why a Game Boy Clone Ran Too Fast — and the DIY Fix Makers Are Building
- ComfyUI on an RTX 3060 12GB: Real Image-Gen Throughput in 2026
- Gemini 3.5 Flash vs Local LLM on RTX 3060 12GB: When Cloud Beats Self-Hosted
- Raspberry Pi 5 Specs: Full 2025 Breakdown
- Best NVMe SSD for a Compact Gaming PC: WD_BLACK SN770 in 2026
- Raspberry Pi 5 8GB Review: Specs, Price & Use Cases (2025)
- 8BitDo Pro 2 on Win98 SE and WinXP: Mapping a Modern Bluetooth Pad to DOSBox, Glide Games, and…
- Best Raspberry Pi Accessories for Home-Lab Builds in 2026
- GeForce4 Ti 4600 tuning guide — ForceWare, Detonator, and XP/98 driver pairing
- Build a Pi Zero W Retro Handheld in 2026: Full Parts List and Setup
- AI-Driven Driver Install for Win98: Vision-LLM + 3060 12GB Build (2026)
- Intel Arc vs NVIDIA 2026: Local LLM Tokens per Dollar
- Best SSD for 2000s LAN Party PC Builds (2026)
Earliest SpecPicks reviews
Browse full archive →- Best GPU for Llama 3.1 8B (2026)
- Best GPU for Qwen 3 14B (2026)
- Best GPU for Qwen 3 32B (2026)
- Best GPU for Llama 3.1 70B (2026)
- Best GPU for DeepSeek-R1 32B (2026)
- Best GPU for Llama 3.1 405B (2026)
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 14B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 70B on NVIDIA GeForce RTX 5090
- How to run DeepSeek-R1 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 4090