BIGTREETECH SKR Pico V1.0 Controller Board Perfectly Compatible with Voron V0.1 3D Printer
Bottom line: The BIGTREETECH SKR Pico V1.0 Controller Board Perfectly ($28.79 on Amazon as of 2026-11-20 23:17 UTC, orderable but not in stock): RP2040 Cortex-M0+ MCU runs Klipper firmware, per the listing; main trade-off: entry-level 4-axis board: no spare driver for a second extruder.
As an Amazon Associate, SpecPicks earns from qualifying purchases. Full disclosure →
*Price sourced from Amazon.com. Last updated 2026-11-20. Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
Pros & Cons
Pros
- ✓ RP2040 Cortex-M0+ MCU runs Klipper firmware, per the listing
- ✓ Onboard TMC2209 drivers in UART mode, so no separate stepper modules are needed
- ✓ Raspberry Pi board footprint lets it mount together with a Pi and save space
- ✓ Larger heat sink gives the drivers more cooling area
- ✓ Side-mounted layout fits the Voron V0's vertical mainboard mount
Cons
- ✗ Entry-level 4-axis board: no spare driver for a second extruder
- ✗ Needs a separate Raspberry Pi host to run Klipper
- ✗ Listing names Klipper only; Marlin support is not stated
- ✗ Onboard drivers can't be swapped for other driver types
SpecPicks Verdict
SpecPicks has no buyer-rating or benchmark data for BIGTREETECH SKR Pico V1.0 Controller Board Perfectly, so this read rests on the manufacturer's listed specs and the current price in the single board computers category (how we evaluate). Compare with similarly-priced alternatives in the single board computers category before committing. On the listing's own facts, the case for it is "RP2040 Cortex-M0+ MCU runs Klipper firmware, per the listing"; the main trade-off is "Entry-level 4-axis board: no spare driver for a second extruder". If those two points fit how you will use it, put it beside one or two close alternatives in the Compare tool to confirm the price.
Before ordering, check the listed dimensions, ports, power requirements and supported devices or systems in the spec table below against how you plan to use it, and confirm them on the retailer's listing. Prices and stock are set by the retailer and may have moved since this page was last updated.
Key Features
Quoted from the manufacturer's listing. Where it differs from the pros and cons above, those note the conditions the listing leaves out.
- Using Raspberry Pi ARM Cortex-M0+ main control RP2040 microprocessor. This controller board onboard UART mode of TMC2209 and supports Klipper firmware
- BIGTREETECH SKR Pico V1.0 main control board heat sink design is newly upgraded, the heat dissipation area is enlarged, and the heat dissipation performance is greatly improved, which is both beautiful and practical
- Chip capacitors (MLCC) of the main control board are all Murata capacitors; well-known brand capacitors, with guaranteed quality and better experience
- Fuse adopts the form of "fuse holder + fuse", which is easy to disassemble; the lateral design of the main control board seat perfectly matches the space characteristics of Voron V0 machine that needs to fix the main board vertically
- ID design is newly upgraded. It adopts the Raspberry-Pi board frame, which is perfectly installation with Rasberry-Pi to save internal space. The appearance and performance coexist. It is the coolest choice for Voron players
Full Specifications
| Brand | BIGTREETECH |
|---|---|
| Color | black |
| Model | KINGPRINTER-1060000513 |
| Material | PCB |
| Unit Count | 1 Count |
| Part Number | KINGPRINTER-1060000513 |
| Display Type | LCD |
| Material Type | PCB |
| Number of Items | 1 |
| Number of Packs | 1 |
| Included Components | BIGTREETECH SKR Pico V1.0 |
| Full listing title | BIGTREETECH SKR Pico V1.0 Controller Board Perfectly Compatible with Voron V0.1 3D Printer, Fits for Raspberry-Pi Using Klipper Firmware, Entry-Level 4-axis DIY Motherboard |
Ready to buy?
BIGTREETECH SKR Pico V1.0 Controller Board Perfectly Compatible with Voron V0.1 3D Printer, Fits for Raspberry-Pi Using Klipper Firmware, Entry-Level 4-axis DIY Motherboard is listed on Amazon. Price, availability, shipping and returns are set by Amazon and its sellers — check the listing for current terms. SpecPicks earns a small commission on qualifying purchases — thank you for supporting independent review work.
*Price sourced from Amazon.com. Last updated 2026-11-20. Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
Related Single Board Computers
More guides & deep dives from the SpecPicks archive
Browse all articles & guides →- Best Retro Handhelds in 2026: Pocket, Mid-Tier and FPGA Picks
- The Complete Voodoo5 5500 AGP Driver Guide (2026 Edition)
- Emulation Hardware in 2026: FPGA, Software, and Cart-Reader Ecosystems
- RTX 4070 Super vs RX 7800 XT — Which to Buy in 2026
- Best 1440p Gaming GPUs in 2026
- How to Build a Windows 98 Retro PC in 2026
- Best Budget Gaming PC Build 2026 — ~$1,000 Parts List
More reviews from the SpecPicks archive
Browse all reviews →- Does Ryzen 3D V-Cache Speed Up CPU-Only LLM Inference?
- Sound BlasterX G6 vs Audigy FX for Modern Retro WinXP Gaming
- AI coding assistants ranked — Claude Code, Cursor, GitHub Copilot, Aider
- Corsair LL120 RGB vs Noctua NH-U12S: Cooling a 5800X for All-Day Gaming
- Sound Blaster AWE64 vs Aureal Vortex 2: The Win98 Audio API War, Revisited
- Qwen 3.6 27B GGUF: BF16 vs Q4_K_M vs Q8_0 Compared
- Raspberry Pi 500 Plus: The Real Lineup vs. the Rumors
- Step 3.7 Flash vs Gemma 4 12B: Which Local Model Wins on a 12GB GPU?
- Best 27-inch 4K Monitor for PC and Console: Odyssey vs KOORUI
- Black Friday Standing Desk & Monitor Arm Deals: 5 Picks
- Black Friday KVM Switch Deals: 5 Picks for Two-PC Desks
- Gemini-SQL2 Tops Text-to-SQL — Can a 12GB RTX 3060 Run Local SQL Models Instead?
- Claude Opus 4.8 Tops GPT-5.5: What Runs Local on a 12GB GPU
- Intel Core Ultra X7 Panther Lake Performance on Linux 7.1
- Best Starter Kit for Learning Robotics on Raspberry Pi (2026)
- Best $500-600 Gaming PC Build for a Ryzen/RX 6600 Rig
- Secluso: Private DIY Home Security on a Raspberry Pi 4
- Best Controller for PC Emulation in 2026: Pro 2 vs DualSense
- Noctua NH-U12S vs DeepCool AK620 on Ryzen in 2026: Honest Pick
- Nemotron 3 Ultra vs MiniMax M3: Best Open Model for a 12GB Rig
- Llama 3.2 3B: Raspberry Pi 4 8GB vs RTX 3060 12GB for Local Inference
- Best Steam Deck Accessories in 2026: Docks, Audio, Controllers, and Storage
- Intel Core Ultra 7 270K Plus: Dual-Channel Memory Scaling Tested
- Best 4K Gaming Monitor for the PS5 Pro and PC in 2026
Earliest SpecPicks reviews
Browse full archive →- Best GPU for Llama 3.1 8B (2026)
- Best GPU for Qwen 3 14B (2026)
- Best GPU for Qwen 3 32B (2026)
- Best GPU for Llama 3.1 70B (2026)
- Best GPU for DeepSeek-R1 32B (2026)
- Best GPU for Llama 3.1 405B (2026)
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 14B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 70B on NVIDIA GeForce RTX 5090
- How to run DeepSeek-R1 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 4090