Skip to main content
10Gbps PoE+ Injector - Powerline Network Adapter, 30W | IEEE 802.3af/at Compliant, 15.4W (PoE) or 30W (PoE+), Up to 100m (328ft), For Cameras, Access Points & IP Phones
ThePoEstore

ThePoEstore 10Gbps PoE+ Injector

Bottom line: The ThePoEstore 10Gbps PoE+ Injector: Adds PoE to any non-PoE switch port without replacing the switch; main trade-off: 30W ceiling: no 802.3bt (60W/90W) support for high-draw devices.

Check price on Amazon

As an Amazon Associate, SpecPicks earns from qualifying purchases. Full disclosure →

Mike Perry — Hardware researcher since 2014. For retro PC hardware and period-correct parts, synthesises manufacturer documentation, community compatibility lists and marketplace listings rather than first-hand lab testing. Core beat: GPU performance across gaming, rendering, and local-LLM inference.

Pros & Cons

Pros

  • ✓ Adds PoE to any non-PoE switch port without replacing the switch
  • ✓ Up to 30W PoE+ output, or 15.4W for 802.3af devices
  • ✓ Runs power and data up to 100m (328ft) over Cat5e/Cat6
  • ✓ Auto power detection with over-voltage and short-circuit protection

Cons

  • ✗ 30W ceiling: no 802.3bt (60W/90W) support for high-draw devices
  • ✗ One injector powers one device; multi-device setups need several units
  • ✗ Listing title says powerline adapter, but this is a PoE injector
  • ✗ Wall-mount hardware and method are not detailed in the listing

Manufacturer description

The ThePoEstore 10Gbps PoE+ Injector lets you power IP cameras, wireless access points and IP phones without replacing your existing non-PoE switch. Place it between the switch and the device, and it sends 48V power and data over one Ethernet cable, so you can mount gear where there is no power outlet. It meets the IEEE 802.3af and 802.3at standards, delivering 15.4W for standard PoE devices or up to 30W for PoE+ hardware. Automatic power detection checks what the connected device needs and supplies only that much, so older 802.3af gear works alongside newer 802.3at equipment. The data path…

SpecPicks Verdict

SpecPicks has no buyer-rating or benchmark data for ThePoEstore 10Gbps PoE+ Injector, so this read rests on the manufacturer's listed specs (how we evaluate). Compare with similarly-priced alternatives in the retro networking cards category before committing. On the listing's own facts, the case for it is "Adds PoE to any non-PoE switch port without replacing the switch"; the main trade-off is "30W ceiling: no 802.3bt (60W/90W) support for high-draw devices". If those two points fit how you will use it, put it beside one or two close alternatives in the Compare tool to confirm the price.

Before ordering, check the listed dimensions, ports, power requirements and supported devices or systems in the spec table below against how you plan to use it, and confirm them on the retailer's listing. Prices and stock are set by the retailer and may have moved since this page was last updated.

Frequently Asked Questions

Can I use this PoE injector with a regular non-PoE switch or router?

Yes. That is what it is for. Connect your existing switch or router to the injector's data input, then run one Ethernet cable from the injector's output to the PoE device. It adds 48V power without any change to your switch.

How much power does it deliver, and will it run my access point or camera?

It supplies up to 30W under IEEE 802.3at (PoE+) or 15.4W under 802.3af (PoE). Automatic detection supplies only what the device requests. Check that your device draws 30W or less. Devices that need 802.3bt power (60W or 90W) are outside its rating.

Does it support multi-gig or 10Gbps network speeds?

Yes. The listing states support for 10/100/1000Mbps plus 2.5Gbps, 5Gbps and 10Gbps link speeds. Real throughput still depends on your switch, the connected device and the grade of cable you run.

How far can I run the cable from the injector to the device?

Up to 100m (328ft) of power and data over Cat5e or Cat6 Ethernet cable, which is the standard maximum Ethernet segment length.

Do I need to install software or configure anything?

No. It is plug-and-play for IP cameras, access points and IP phones. It needs no drivers, management interface or setup. Power negotiation with 802.3af/at devices happens automatically.

Key Features

Quoted from the manufacturer's listing. Where it differs from the pros and cons above, those note the conditions the listing leaves out.

  • Convert Non-PoE to PoE: Upgrade your network with a 30W/48V PoE+ injector, enabling PoE without replacing existing switches
  • IEEE802.3af/at Compliant: Delivers power and data over a single Ethernet cable for areas without power outlets
  • 10Gbps High-Speed Performance: Supports 10/100/1000Mbps/2.5/5/10Gbps speeds with protection against over voltage and short circuits
  • Long-Range Connectivity: Extend power and data up to 100m (328ft) using Cat5e/Cat6 cables for remote devices
  • Plug-and-Play Setup: No software or configuration needed for IP cameras and access points
  • Versatile Mounting Options: Durable white shell design allows flexible placement on desk or wall mounting for convenient installation

Full Specifications

BrandThePoEstore
ColorPoE30W-White-10GB
Unit Count1.0 Count
Model NumberPoE30W-White-10GB
Built-In Media1 x AC Cord, 1 x PoE Body, 1 x Product Manual
Number of Items1
Compatible DevicesInternet Protocol Camera
Data Link ProtocolIEEE 802.3
Data Transfer Rate10 Gigabits Per Second
Hardware InterfaceEthernet
Plug-and-Play SetupNo software or configuration needed for IP cameras and access points
Warranty Description4 Year Manufacturer
Convert Non-PoE to PoEUpgrade your network with a 30W/48V PoE+ injector, enabling PoE without replacing existing switches
Long-Range ConnectivityExtend power and data up to 100m (328ft) using Cat5e/Cat6 cables for remote devices
IEEE802.3af/at CompliantDelivers power and data over a single Ethernet cable for areas without power outlets
Automatic Power DetectionAutomatically detects and delivers the required power up to 30W with backward compatibility for 802.3af/at standards
Versatile Mounting OptionsDurable white shell design allows flexible placement on desk or wall mounting for convenient installation
10Gbps High-Speed PerformanceSupports 10/100/1000Mbps/2.5/5/10Gbps speeds with protection against over voltage and short circuits
Full listing title10Gbps PoE+ Injector - Powerline Network Adapter, 30W | IEEE 802.3af/at Compliant, 15.4W (PoE) or 30W (PoE+), Up to 100m (328ft), For Cameras, Access Points & IP Phones

Ready to buy?

10Gbps PoE+ Injector - Powerline Network Adapter, 30W | IEEE 802.3af/at Compliant, 15.4W (PoE) or 30W (PoE+), Up to 100m (328ft), For Cameras, Access Points & IP Phones is listed on Amazon. Price, availability, shipping and returns are set by Amazon and its sellers — check the listing for current terms. SpecPicks earns a small commission on qualifying purchases — thank you for supporting independent review work.

Check price on Amazon →

Related Retro Networking Cards

More guides & deep dives from the SpecPicks archive

Browse all articles & guides →

More reviews from the SpecPicks archive

Browse all reviews →

Earliest SpecPicks reviews

Browse full archive →