AURSINC 2025 Upgraded V1.5.2 MMDVM Hotspot Spot Radio Station WiFi Digital Voice Modem Work Contained with Raspberry Pi Zero 2W, Supports C4FM YSF POCSAG NXDN DSTAR P25 DMR, Pi-Star/WPSD
Bottom line: The AURSINC 2025 Upgraded V1.5.2 MMDVM Hotspot Spot Radio Station WiFi ($139.99 on Amazon as of 2026-10-24 10:13 UTC): Raspberry Pi Zero 2W built in, so you don't need to source a separate board; main trade-off: pi Zero 2W WiFi is 2.4GHz only, so 5GHz networks will not connect.
As an Amazon Associate, SpecPicks earns from qualifying purchases. Full disclosure →
*Price sourced from Amazon.com. Last updated 2026-10-24. Price and availability subject to change.
Pros & Cons
Pros
- ✓ Raspberry Pi Zero 2W built in, so you don't need to source a separate board
- ✓ Pi-Star preloaded on the TF card, so there's no initial download or flashing
- ✓ Covers DMR, D-STAR, C4FM YSF, P25, NXDN and POCSAG on UHF 430-440 MHz
- ✓ RX/TX offsets default to 0 on this upgraded board, skipping a common calibration step
- ✓ Micro USB power works from a power bank or in a vehicle tethered to a phone
Cons
- ✗ Pi Zero 2W WiFi is 2.4GHz only, so 5GHz networks will not connect
- ✗ Requires WPA WiFi security; WEP-protected networks are not supported
- ✗ Not compatible with Baofeng UV-5R, RD-5R, 5X, 5R Plus or other UV/BF series radios
- ✗ Tested in DMR mode; other modes need their parameters set manually in Pi-Star
Manufacturer description
The AURSINC MMDVM hotspot gives you a ready-to-run digital voice gateway built around a Raspberry Pi Zero 2W. You don't need to source a separate board or flash an image to get started. Pi-Star comes preloaded on the included TF card, so setup comes down to joining your WiFi network and opening the Pi-Star configuration page. This upgraded board covers DMR, D-STAR, C4FM YSF, P25 and NXDN, and the listing also names POCSAG. It works on UHF from 430 to 440 MHz. The RX and TX offsets default to 0, so you skip a calibration step that older MMDVM boards often needed. The manufacturer tests the…
SpecPicks Verdict
SpecPicks scored AURSINC 2025 Upgraded V1.5.2 MMDVM Hotspot Spot Radio Station WiFi… using a rating × review-volume × price-fit model applied to published specs and reviews across the single-board computers category. AURSINC's single-board computers lineup sits within the broader category mid-tier; price and specs are the deciding factors over brand loyalty here. Judge it on the specification table and the price rather than on sentiment: check the figures that decide your use case, then put it side-by-side with two or three close alternatives in the Compare tool before clicking through.
Common buyer scenarios for single-board computers of this kind: matching it to an existing build, replacing a failing part, or upgrading from a previous-generation equivalent. Check the spec table below against your current setup — particularly socket / form-factor / power-rating fields — and confirm compatibility on the retailer's listing before purchase. Prices and stock are set by the retailer and may have moved since this page was last updated.
Frequently Asked Questions
Does the AURSINC MMDVM hotspot come with Pi-Star already installed?
Yes. Pi-Star is preloaded on the included TF card, so you don't need to download it. If you later flash a newer image, write it to the card with an imaging tool. Copying the files directly onto the card will not work.
Will this hotspot work with my Baofeng UV-5R?
No. The manufacturer says it is not compatible with the Baofeng UV-5R, RD-5R, 5X, 5R+ or 5R Plus, or with other Baofeng UV and BF series radios. You need a UHF radio that supports one of the hotspot's digital modes: DMR, D-STAR, C4FM YSF, P25 or NXDN.
Why won't the hotspot connect to my home WiFi?
The Raspberry Pi Zero 2W supports only 2.4GHz WiFi, so it won't join a 5GHz network. The network must also use WPA security, not WEP. After you power the unit on, wait about 2 minutes for it to connect, then open the Pi-Star /admin/configure.php page.
What frequency range does it operate on, and do I need to set RX/TX offsets?
It operates on UHF from 430 to 440 MHz. On this upgraded version, the RXOFFSET and TXOFFSET values default to 0, so you don't need to adjust them during initial setup.
Can I use the hotspot in my car, and can the firmware be updated?
Yes. It runs on micro USB power, and a cable is included, so you can power it from a power bank or a laptop. Tether it to your phone's mobile data for use in a vehicle. The MMDVM board ships with firmware V1.5.2 and can be updated to V1.6.1 for WPSD.
Key Features
- [Upgrade] AURSINC MMDVM radio station now equipped with raspberry pi zero 2w. Experience faster processing, smoother WiFi performance, and enhanced Stability
- [EASY SET UP] Preload sofeware Pi-Star on TF card, no need to download again. Radio Frequency (UHF430-440) This is upgraded version, do not need to set RXOFFSET and TXOFFSET, they're default 0. Note when you flash the TF card with new version software, please DO NOT copy on the TF card directly, use a write in tool to write the software on TF card
- [EASY CHARGING] Free micro USB charging cable included, charged with power bank or connect to laptop or computer. The Hotspot will also work mobile in your vehicle if you tether it to your mobile phone network
- [FIRMWARE V1.5.2] The MMDVM hotspot board supports updating to V1.6.1 (How to Update MMDVM_HS for WPSD 1.6.1 jumbo5566 .github.io). To speed up the operation, it is recommended to switch to an optimized system:https// w0chp.radio/ wpsd/
- [SUPPORT] C4FM YSF NXDN DSTAR P25 DMR and default work with UHF. Not compatible with Baofeng UV-5R, Baofeng RD-5R, 5X, 5R+, 5R Plus, etc UV series, BF series. Our test is in DMR mode, if you want to change the working mode, you need to configure it as needed Working mode parameters
- [WIFI SSID] Need the 2.4GHz SSID as Pi Zero 2W doesn't support 5.8GHz. Ensure WiFi Password Type is WPA, not WEP. Power on hotspot for 2 minutes to auto-connect or follow instructions to connect the Hotspot to your router. After power on 2 minutes, go to pi-star /admin/ configure.php
Full Specifications
| UPC | 753318593206 |
|---|---|
| ASIN | B088PPDRT7 |
| Brand | AURSINC |
| Color | Black |
| Modem Type | Network Modem |
| Unit Count | 1.0 Count |
| Item Weight | 3.5 Ounces |
| Manufacturer | AURSINC |
| Built-In Media | Antenna (with 90 degree elbow), MMDVM Hotspot Spot Radio Station, Raspberry Pi Zero 2W, TF card |
| Item Type Name | [NOTE] If you encounter that the device cannot connect to network after setup, please reflash the SD Card by using the software package, the path for the package drive.google. com/file/d/1pL8077KkEVoKuIXHsdQVQgsH3FY8CFZf/view?usp=sharing . if it still not working, please reach out to us through mail, we will address your issue asap. |
| Number of Ports | 3 |
| Compatible Devices | Raspberry pi Zero W/2W |
| Product Dimensions | 2.8"L x 1.3"W x 1.6"H |
| Warranty Description | 30days |
| Connectivity Technology | Ethernet, USB, Wi-Fi |
| Number of Ethernet Ports | 1 |
| Internet Service Provider | Pi star, WPSD |
| Internet service provider | Pi star, WPSD |
| Item Dimensions L x W x H | 2.8"L x 1.3"W x 1.6"H |
Hardware benchmark data
Ready to buy?
AURSINC 2025 Upgraded V1.5.2 MMDVM Hotspot Spot Radio Station WiFi Digital Voice Modem Work Contained with Raspberry Pi Zero 2W, Supports C4FM YSF POCSAG NXDN DSTAR P25 DMR, Pi-Star/WPSD is listed on Amazon. Price, availability, shipping and returns are set by Amazon and its sellers — check the listing for current terms. SpecPicks earns a small commission on qualifying purchases — thank you for supporting independent review work.
*Price sourced from Amazon.com. Last updated 2026-10-24. Price and availability subject to change.
AURSINC 2025 Upgraded V1.5.2 MMDVM Hotspot Spot… head-to-head
Side-by-side specs, prices, and a pick for each matchup — no tab-switching.
More guides & deep dives from the SpecPicks archive
Browse all articles & guides →- RTX 4070 Super vs RX 7800 XT — Which to Buy in 2026
- Emulation Hardware in 2026: FPGA, Software, and Cart-Reader Ecosystems
- How to Build a Windows 98 Retro PC in 2026
- Best 1440p Gaming GPUs in 2026
- The Complete Voodoo5 5500 AGP Driver Guide (2026 Edition)
- Best Budget Gaming PC Build 2026 — ~$1,000 Parts List
- Best Retro Handhelds in 2026 — From $35 to $500
More reviews from the SpecPicks archive
Browse all reviews →- Best Budget SSD for Gaming and PC Upgrades in 2026
- 3dfx Voodoo5 5500 PCI Boots in a Modern ASUS Z77 Board
- Prime Intellect's $130M raise: build your own agent rig
- Best CPU Coolers for Ryzen & Intel Gaming Builds in 2026
- Best 4K Monitor for PS5 and Xbox Series X Console Gaming in 2026
- Best Gaming Webcam and Microphone Bundle for Streamers in 2026
- Can a Raspberry Pi 4 Run the Oomwoo Open-Source Robot Vacuum Brain?
- Corsair's New Gaming Mouse Has a Dedicated Stream Deck Launch Button
- Best Raspberry Pi Alternative for Klipper in 2026 (and When the Pi Still Wins)
- RX 9060 XT vs RX 9070 XT: OLED 1440p or 4K IPS?
- AMD RX 9070 XT Hits All-Time-Low $629 in Amazon Lightning Sale
- Best Raspberry Pi Accessories for Home-Lab Builds in 2026
- Retro Nintendo Switch 2 Dock Channels the N64 and Holds Six Game Cards
- Sound Blaster Audigy FX in a Period-Correct WinXP Build: 2026 Install and Tuning Guide
- Prime Intellect Raises $130M to Help Enterprises Build Their Own AI Agents
- Build a Self-Updating 24/7 FM Radio Station on a Raspberry Pi Zero W
- PiKVM Hardware Requirements: The Real 2026 Guide
- Best PC Gaming Gear for Console Players Making the Switch in 2026
- vLLM vs llama.cpp for Single-User Chat on a 12GB GPU (2026)
- Building a 2001 Pentium III + GeForce 3 Win98SE Gaming Rig: A 2026 Build Log
- Intel i7-9700K vs Ryzen 7 5700X for a Budget 2026 Gaming Build
- RTX 5090 AI TOPS: What the Official Number Means
- Handheld Gaming PC Near Me: Where to Buy in 2025
- Forza Horizon 6: 8GB vs 16GB VRAM GPU Benchmark Guide
Earliest SpecPicks reviews
Browse full archive →- Best GPU for Llama 3.1 8B (2026)
- Best GPU for Qwen 3 14B (2026)
- Best GPU for Qwen 3 32B (2026)
- Best GPU for Llama 3.1 70B (2026)
- Best GPU for DeepSeek-R1 32B (2026)
- Best GPU for Llama 3.1 405B (2026)
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 14B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 70B on NVIDIA GeForce RTX 5090
- How to run DeepSeek-R1 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 4090