Skip to main content
EZDIY-FAB Adapter Cable for Corsair Lighting Node Pro and for Corsair iCUE Commander PRO (hub is not Included), Smart RGB Lighting, Connect to Any 5V 3-Pin ARGB Devices (2 x 20cm)
EZDIY-FAB

EZDIY-FAB Adapter Cable

Bottom line: The EZDIY-FAB Adapter Cable: Brings any 5V 3-pin ARGB device under Corsair iCUE control; main trade-off: corsair Lighting Node Pro or Commander PRO hub not included.

Check price on Amazon

As an Amazon Associate, SpecPicks earns from qualifying purchases. Full disclosure →

Mike Perry — Hardware researcher since 2014, focused on GPU performance across gaming, rendering, and local-LLM inference. Synthesises community benchmarks, manufacturer specs, and public forum data into actionable buying guides.

Pros & Cons

Pros

  • ✓ Brings any 5V 3-pin ARGB device under Corsair iCUE control
  • ✓ Works with both Lighting Node Pro and iCUE Commander PRO
  • ✓ Two cables per pack for two separate ARGB devices or chains
  • ✓ 20cm (7.8 in.) length reaches nearby fans and strips
  • ✓ Lets mixed-brand lighting sync from one software suite

Cons

  • ✗ Corsair Lighting Node Pro or Commander PRO hub not included
  • ✗ Not compatible with 12V 4-pin RGB devices
  • ✗ 20cm length may be too short for larger cases or remote mounts
  • ✗ Only useful if your build already runs Corsair iCUE hardware

Manufacturer description

The EZDIY-FAB Adapter Cable lets you control non-Corsair addressable RGB gear from a Corsair Lighting Node Pro or Corsair iCUE Commander PRO. If you already run your lighting through Corsair's iCUE software but have fans, strips or other accessories with standard 5V 3-pin ARGB connectors, these adapters bridge the two so everything can be managed from one place. The pack includes two adapter cables, each 20cm (7.8 in.) long. That gives you enough length to route from a hub mounted on the case floor or behind the motherboard tray to nearby ARGB devices. Because there are two cables, you can…

SpecPicks Verdict

SpecPicks has no buyer-rating or benchmark data for EZDIY-FAB Adapter Cable, so this read rests on the manufacturer's listed specs (how we evaluate). Compare with similarly-priced alternatives in the rgb & lighting category before committing. On the listing's own facts, the case for it is "Brings any 5V 3-pin ARGB device under Corsair iCUE control"; the main trade-off is "Corsair Lighting Node Pro or Commander PRO hub not included". If those two points fit how you will use it, put it beside one or two close alternatives in the Compare tool to confirm the price.

Before ordering, check the listed dimensions, ports, power requirements and supported devices or systems in the spec table below against how you plan to use it, and confirm them on the retailer's listing. Prices and stock are set by the retailer and may have moved since this page was last updated.

Frequently Asked Questions

Does this come with the Corsair Lighting Node Pro or Commander PRO hub?

No. The hub is not included. You need a Corsair Lighting Node Pro or Corsair iCUE Commander PRO already installed to use these adapter cables.

Will this work with my 12V 4-pin RGB fans?

No. The adapter is designed for 5V 3-pin ARGB (addressable RGB) connectors only. Confirm your device uses a 5V 3-pin plug before buying.

How long are the adapter cables and how many come in the pack?

The pack includes two adapter cables, each 20cm (7.8 in.) long.

Can I control non-Corsair ARGB devices in iCUE with this adapter?

Yes. Once connected to a Lighting Node Pro or Commander PRO, any 5V 3-pin ARGB device can be controlled through Corsair's iCUE software.

How many LEDs or devices can I run from one adapter?

The listing does not specify an LED or device limit. Check the specs of your Corsair hub and your ARGB devices, or the manufacturer's product listing, for supported channel loads.

Key Features

Quoted from the manufacturer's listing. Where it differs from the pros and cons above, those note the conditions the listing leaves out.

  • This adapter could connect to any 5V ARGB devices and controlled by Corsair node ICUE software
  • Each adapter cable 20cm/7.8 in.
  • Make sure your RGB device with 5V 3-Pin connector
  • WARNNING: CORSAIR Hub is not included!!!!!

Full Specifications

BrandEZDIY-FAB
ColorBlack
ModelUS-NEW ICUE cable for led strips
WARNNINGCORSAIR Hub is not included!!!!!
Cable TypeLightning
Item ShapeRound
Model NameUS-NEW ICUE cable for led strips
Unit Count1 Count
Item Length20 Centimeters
Part NumberUS-NEW ICUE cable for led strips
Connector TypeUsb
Number of Pins3
Maximum Voltage5 Volts
Number of Items2
Special FeatureLightweight
Connector GenderMale-to-Female
Specification MetNo
Compatible DevicesPersonal Computer
Indoor Outdoor UsageIndoor, Outdoor
Customer Package TypeStandard Packaging
Full listing titleEZDIY-FAB Adapter Cable for Corsair Lighting Node Pro and for Corsair iCUE Commander PRO (hub is not Included), Smart RGB Lighting, Connect to Any 5V 3-Pin ARGB Devices (2 x 20cm)

Ready to buy?

EZDIY-FAB Adapter Cable for Corsair Lighting Node Pro and for Corsair iCUE Commander PRO (hub is not Included), Smart RGB Lighting, Connect to Any 5V 3-Pin ARGB Devices (2 x 20cm) is listed on Amazon. Price, availability, shipping and returns are set by Amazon and its sellers — check the listing for current terms. SpecPicks earns a small commission on qualifying purchases — thank you for supporting independent review work.

Check price on Amazon →

Related RGB & Lighting

More guides & deep dives from the SpecPicks archive

Browse all articles & guides →

More reviews from the SpecPicks archive

Browse all reviews →

Earliest SpecPicks reviews

Browse full archive →