MOOKEERF RG8X BNC Male to BNC Male Coaxial Cable 3FT 50 ohm Ultra Low Loss for Antenna
Bottom line: The MOOKEERF RG8X BNC Male to BNC Male Coaxial Cable 3FT 50 ohm Ultra Low: Rated VSWR of 1.15 or lower for clean, low-reflection RF runs; main trade-off: 50 ohm only; wrong impedance for 75 ohm RGB, SDI or CCTV video.
As an Amazon Associate, SpecPicks earns from qualifying purchases. Full disclosure →
Pros & Cons
Pros
- ✓ Rated VSWR of 1.15 or lower for clean, low-reflection RF runs
- ✓ Low-loss RG8X: -2.65dB over 25ft at 1800MHz per maker spec
- ✓ Pure copper center conductor with 95% tinned copper braid shield
- ✓ 2.2" adhesive tube holds each BNC connector against pull-off
- ✓ Waterproof, oxidation-resistant PVC jacket for outdoor antenna use
Cons
- ✗ 50 ohm only; wrong impedance for 75 ohm RGB, SDI or CCTV video
- ✗ Loss spec is quoted for 25ft, not for this 3ft length
- ✗ RG8X is thicker and stiffer than RG58 for tight bench routing
- ✗ BNC male on both ends; SMA, N or PL-259 gear needs adapters
Manufacturer description
The MOOKEERF RG8X BNC Male to BNC Male Coaxial Cable is a 3ft, 50 ohm jumper for RF benches and radio shacks. Both ends have BNC male connectors, so you can link an oscilloscope, spectrum analyzer, signal generator, splitter or 3G/4G/LTE antenna to any device with a BNC port. The cable uses RG8X, which is thicker than budget RG58 patch leads. MOOKEERF rates its attenuation as low as -2.65dB over 25ft at 1800MHz, with VSWR held at 1.15 or lower, so a 3ft run adds very little loss to your measurements. The center conductor is pure copper, and a 95% tinned copper braid shields it from…
SpecPicks Verdict
SpecPicks has no buyer-rating or benchmark data for MOOKEERF RG8X BNC Male to BNC Male Coaxial Cable 3FT 50 ohm Ultra…, so this read rests on the manufacturer's listed specs (how we evaluate). Compare with similarly-priced alternatives in the retro crt & display accessories category before committing. On the listing's own facts, the case for it is "Rated VSWR of 1.15 or lower for clean, low-reflection RF runs"; the main trade-off is "50 ohm only; wrong impedance for 75 ohm RGB, SDI or CCTV video". If those two points fit how you will use it, put it beside one or two close alternatives in the Compare tool to confirm the price.
Before ordering, check the listed dimensions, ports, power requirements and supported devices or systems in the spec table below against how you plan to use it, and confirm them on the retailer's listing. Prices and stock are set by the retailer and may have moved since this page was last updated.
Frequently Asked Questions
What impedance is this MOOKEERF BNC cable?
It is 50 ohm, the standard for RF radio, antennas, oscilloscopes, spectrum analyzers and signal generators. It is not meant for 75 ohm video or CCTV systems.
How long is the cable and what connectors does it have?
The cable is 3ft long, with a BNC male connector on each end. It is built from RG8X coaxial cable.
How much signal loss should I expect?
MOOKEERF rates the RG8X cable at -2.65dB over 25ft at 1800MHz, with VSWR at 1.15 or lower. At 3ft, total loss will be a small fraction of that 25ft figure.
Can I use this cable outdoors?
Yes. The PVC jacket is listed as waterproof and resistant to oxidation for long-term outdoor use. The pure copper core and 95% tinned copper braid help keep the signal stable.
Will it work with my LTE antenna or splitter?
It works with any device that has a female BNC port, including splitters, 3G/4G/LTE antennas, oscilloscopes, analyzers and network systems. Devices with SMA or N-type ports need a BNC adapter.
Key Features
Quoted from the manufacturer's listing. Where it differs from the pros and cons above, those note the conditions the listing leaves out.
- [Specification]-Connector: BNC male to BNC male, impedance: 50 ohm, Cable type: RG8X.
- [Ultra Low Loss]-The RG8X jumper cable got a professional structure and take good advantage in transmit data with lower signal attenuation that low to -2.65db(25ft,1800MHz) and keep VSWR≤1.15.
- [Firm Connected]-We fix the connector with 2.2" adhesive tube and it will not easy to fall off from the cable. And that can provide a heavy duty and firmly connection, really durable and professional coaxial cable.
- [High Grade Material]-This RG8X BNC cable inner conductor is made by pure copper and build with 95% tinned copper braid, that can make sure the signal transmission efficiently and stable. The PVC jacket is waterproof and has strong oxidation resistance, and can be adapted to outdoor for a long time.
- [Widely Application]-Compatible with device which contain BNC connector, including splitter, 3G/4G/LTE antenna, Oscilloscope, Spectrum, Analyzer and Network systems etc.
Full Specifications
| Brand | MOOKEERF |
|---|---|
| Color | Black |
| Model | RG8X-BNC-JJ-3FT |
| Weight | 3g |
| Wattage | 8.08 watts |
| Frequency | 2 GHz |
| Cable Type | Coaxial |
| Item Shape | Round |
| Unit Count | 3 Feet |
| Item Length | 3 feet |
| Part Number | RG8X-BNC-JJ-3FT |
| Connector Type | BNC |
| Number of Pins | 2 |
| Outer Material | Polyvinyl Chloride (PVC) |
| Number of Items | 1 |
| Special Feature | gps |
| Connector Gender | Male-to-Male |
| Compatible Devices | Router |
| Data Transfer Rate | 3 gigabits_per_second |
| Indoor Outdoor Usage | Indoor, Outdoor |
| Full listing title | MOOKEERF RG8X BNC Male to BNC Male Coaxial Cable 3FT 50 ohm Ultra Low Loss for Antenna, RF Radio, Modem, Oscilloscope, Spectrum, Analyzer, Signal Generator |
Ready to buy?
MOOKEERF RG8X BNC Male to BNC Male Coaxial Cable 3FT 50 ohm Ultra Low Loss for Antenna, RF Radio, Modem, Oscilloscope, Spectrum, Analyzer, Signal Generator is listed on Amazon. Price, availability, shipping and returns are set by Amazon and its sellers — check the listing for current terms. SpecPicks earns a small commission on qualifying purchases — thank you for supporting independent review work.
Related Retro CRT & Display Accessories
More guides & deep dives from the SpecPicks archive
Browse all articles & guides →- The Complete Voodoo5 5500 AGP Driver Guide (2026 Edition)
- How to Build a Windows 98 Retro PC in 2026
- Emulation Hardware in 2026: FPGA, Software, and Cart-Reader Ecosystems
- RTX 4070 Super vs RX 7800 XT — Which to Buy in 2026
- Best Budget Gaming PC Build 2026 — ~$1,000 Parts List
- Best 1440p Gaming GPUs in 2026
- Best Retro Handhelds in 2026: Pocket, Mid-Tier and FPGA Picks
More reviews from the SpecPicks archive
Browse all reviews →- $1,000 Gaming PC Build 2026: Parts, Cost, 1080p FPS
- vLLM 0.21 Adds Intel Arc Support: The Local Stack Widens
- Amazon RTX 5060 Deal: $324 Budget GPU for 1080p Gaming
- Run DeepSeek & Qwen Locally on an RTX 3060 12GB (2026 Guide)
- llama.cpp on Snapdragon Hexagon NPU: First Real Benchmarks and What Actually Works
- Best Retro Gaming Console to Buy in 2026
- Logitech G502 Hero vs HyperX QuadCast 2 S vs Elgato Cam Link 4K: Building a Sub-$300 Streaming Starter Kit
- DIY Pinball Controller for Retro Gaming: Build Guide
- Microsoft's SkillOpt Boosts GPT-5.5 With Just a Trained Markdown File
- Is vLLM Worth It If You're Not Serving Other Users?
- How to run Llama 3.1 8B on Apple M4 Pro (2026)
- Ryzen 7 5800X vs Ryzen 7 5700X: Which 8-Core AM4 Chip to Buy in 2026
- Sound Blaster Audigy FX Install Guide for Win98 SE Period-Correct Builds
- Best GPU for Qwen3 8B in 2026
- Boot Windows 98 from CompactFlash: A Silent, Reliable CF-to-IDE Build
- Voodoo5 5500 PCI Boots on Modern ASUS P8Z77-V Pro — A Look at Retro GPUs in 2026 Boards
- Claude Opus 4.8 Tops the Intelligence Index: Cloud vs Local on a 3060
- Mount a 90s Big-Box CD-ROM ISO on Win98 Without a CD Drive
- Best Quiet PC Cooling Upgrades in 2026
- Corsair Launches Lightweight Budget HS35 v3 Gaming Headset
- Best Budget 4K Gaming Monitor in 2026
- Claude Code + Fable 5 Ported Command & Conquer to iOS in Hours: What Local Coding Rigs Need
- Intel's Bartlett Lake Core 9 273PQE Loses to a Four-Year-Old CPU
- Best 4K Monitor for PS5 and Console Gaming Under $400 (2026)
Earliest SpecPicks reviews
Browse full archive →- Best GPU for Llama 3.1 8B (2026)
- Best GPU for Qwen 3 14B (2026)
- Best GPU for Qwen 3 32B (2026)
- Best GPU for Llama 3.1 70B (2026)
- Best GPU for DeepSeek-R1 32B (2026)
- Best GPU for Llama 3.1 405B (2026)
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 14B on NVIDIA GeForce RTX 5090
- How to run Qwen 3 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 70B on NVIDIA GeForce RTX 5090
- How to run DeepSeek-R1 32B on NVIDIA GeForce RTX 5090
- How to run Llama 3.1 8B on NVIDIA GeForce RTX 4090